Studio Desk Makeover – Half 3 – Including Trim, Furnishings Ft, and Different Particulars

First, let me again up and remind you of the errors that I made on my first try so as to add panels to the prevailing desk. Not solely did I set up the facet ornamental vine panels the other way up. (To my eye, the vines wanted to “develop” up and never down.) However I additionally made the error of pondering I may simply add boards to the within of the higher space to cover the drawers that I’ll be including.

So what I ended up with was this — an the other way up vine and an higher space that regarded prefer it needed to be an inset panel however failed as a result of the board was set method too far again. And it regarded awkward having the higher panel and the decrease ornamental panel set at completely different factors on the two″ x 2″ boards that shaped the body of the desk.

To right my errors, I wanted to begin by eradicating the ornamental panel. I used my Dremel Multi-Max to chop alongside the perimeters via the nails that have been holding the panel in. That left some gouges within the body items, so I needed to fill these with wooden filler and sand to easy out the harm.

After which after reducing the piece for the higher panel on my desk noticed in order that it could match contained in the body items, I used a chunk of 1/4-inch board as a spacer to connect it. That is a type of specialty boards that you will discover at Residence Depot or a craft retailer.

So I used this as a spacer whereas putting in the entire panels to ensure they have been all set into the desk body on the identical level.

Right here’s what the highest panel regarded like set contained in the body versus attaching behind the body.

It regarded so significantly better this manner! I connected it utilizing 16-gauge nails shot via the body items above and under the panel, and into the perimeters of the panel. (The desktop isn’t at present connected, so I simply moved it over to entry the highest body piece so I may nail via it and into the highest fringe of the panel.)

After which I used the identical spacer to re-install the ornamental panel.

That regarded so significantly better! All the things regarded deliberate and intentional this time. Earlier than, it regarded haphazard and like an afterthought.

Within the photos under, you may actually see the distinction that it made to carry these higher panels ahead contained in the desk body. Right here’s what it regarded like earlier than with the boards connected to the again of the desk body. Like this, the boards have been set again 1.5 inches…

And right here’s what it appears to be like like after reducing the boards to suit contained in the desk body, and transferring these boards ahead contained in the body in order that they’re set again only one/4 inch…

After getting the entire panels in place, I began including trim. That is the place I actually began making stuff up as I went alongside. 😀 I used some cupboard trim from Residence Depot (the sort that’s offered by the 8-foot piece and never by the linear foot) and determined to connect it to the entire horizontal desk body items. I favored the trim, the panels, and the leaf design. What I didn’t like was how these sq. legs regarded from the underside trim to the ground.

It regarded like I had taken a Parson’s desk and added trim to it to make it look conventional in model. It regarded very odd to my eye. So I headed to Residence Depot and purchased some furnishings legs. The size of the leg from the underside of the trim under the ornamental panel to the ground was six inches. The one six-inch furnishings legs that have been slim sufficient to make use of on my desk and that I may discover domestically have been these…

I wasn’t thrilled about it. I had vowed by no means to make use of these legs once more on any mission as a result of they’re so ubiquitous on DIY furnishings tasks just because they’re so available at each Residence Depot and Lowe’s. However I both had to make use of these or wait a number of days for an internet order to indicate up, and I simply wasn’t keen to attend. In order that left me with one selection. I had to make use of these.

So I flipped the desk over on its again…

After which I used a handsaw to chop off the leg under the trim…

And I used to be left with this…

Residence Depot didn’t have the metallic inserts that match the screw on these legs, and the plates they promote to simply connect these legs to furnishings have been method too massive to suit this space of my desk. So I simply drilled a gap within the desk leg that was a dimension smaller than the screw prime on the furnishings leg, coated the highest of the furnishings leg with wooden glue, after which screwed it in. Then I bolstered it with some nails shot at an angle via the highest fringe of the legs and angled into the underside of the desk leg. As soon as the glue dried, the brand new legs have been very safe.

After flipping the desk over and repeating that on the again leg, that is what it regarded like.

Despite the fact that these aren’t my favourite furnishings toes, I assumed this regarded so significantly better than having these plain, sq. legs going all the best way to the ground.

After repeating that course of on the legs on the opposite facet of the desk, the essential construct for the desk base was completed.

I did get the entire wooden filling achieved final night time earlier than I went to mattress (nail holes, mitered trim corners, and so forth.), so I’m hoping that I can get this base completed at present.

I’ll have to sand the entire wooden filler, after which prime the entire thing and provides it a fast sanding once more earlier than portray. I’ll additionally have to do some caulking to repair a few of the areas across the ornamental panels the place my Dremel Multi-Max left some fairly tough cuts. However I’m actually hoping that I can have this completed at present and get began on the desktop. I received’t have the ability to connect the drawers till the desktop is completed and in place.