Easy methods to Simply Reduce Crown Molding This Jig Saves So A lot Time | Thrifty Decor Chick

This crown slicing jig makes slicing and putting in crown molding a BREEZE!

In the event you’ve ever lower crown molding on a miter noticed, you understand what a ache it may be. I used to must maintain instance items of molding with the cuts close by to remind myself each time I do it as a result of it may be so complicated. 

To get the proper lower, there’s a number of flipping and reversing (anybody else singing “is it value it, let me work it?”), and ensuring the crown lays excellent on the noticed.

I’ve tried coping the crown molding joints (utilizing a hand noticed to “cope” the ends of the crown) and may by no means get it proper. 

However THIS, my pals, is one of the best technique of all of them!

In the event you’ve examine my initiatives for any size of time, you understand how a lot I really like ornamental trim and molding in a room. 

It provides a lot!:

I not too long ago completed up the molding in our basement utilizing this beneficial jig, and it took half the time it used to: 

I am SO glad to have this accomplished! It solely took two years. 🙂 

This small room has eight corners although, and slicing crown molding is considered one of my least favourite DIY jobs. Putting in is not dangerous, however the slicing is a ache! 

So I lastly regarded picked up this crown slicing device I’ve seen just a few instances on-line. 

I watched the video and stored saying to myself…there’s no means it is that simple. I used to be fallacious!

First up, they supply these little angle finders which might be saved on the jig: 

Place your crown on a flat floor (wall or a desk) and place the angle piece contained in the again of the molding until you get the fitting match. 

For instance, this one is just not good:

However this one (38 diploma angle) is ideal!:

Crown molding is available in just a few “spring angles” so these little angle finders are extremely useful!

Earlier than you begin slicing, you may wish to place your jig on the proper angle top: 

That is what retains it on the good angle whereas slicing the crown molding on the noticed.

Their video shares the place to position the jig for each inside and outdoors nook cuts, in addition to the path your noticed blade ought to be going. (There are additionally photographs on the precise jig to reference.)

I attempted my first piece of molding, held it up within the nook, and began to consider. 😉 

I laughed out loud once I held the primary two items up subsequent to one another they usually matched completely. I imply…the place has this factor been all my life?? 

To make use of this jig in your noticed, all it’s a must to do is place your crown in entrance of the noticed fence (ornamental facet out), then push the jig as much as it. 

You will wish to be sure that the underside of the crown is flush towards the noticed guard on the backside and the highest of the crown is leaning towards the jig: 

Ensure your jig is out of the best way of the noticed blade, then lower within the path to your inside or exterior lower. 

Most corners would require a 45-degree miter lower, however sometimes I’ve wanted a 33 or 23-degree angle. 

The visuals for the angled cuts on the jig are extremely useful — it is a bit complicated to recollect at first, however after just a few cuts you may get it down fast. 

It reveals you the right way to lower each the left and proper facet, for inside and outdoors corners:

You will wish to mark your measurements on the again of your crown, not the entrance, as a result of all your cuts can be produced from the again of the molding. 

That is good since you do not mark up the entrance of your trim with a pencil line!

My first two items with this device had been for an outdoor nook they usually met up PERFECTLY. Have a look at that tight seam!:

And the within nook items had been glorious as properly!:

I can not let you know how a lot time (and precise crown molding!) this jig has saved me! When utilizing a compound miter noticed with out this jig, it’s a must to keep in mind the right way to place the crown, flip it the other way up to chop from the underside of the crown, and so on. 

Despite the fact that I’ve lower crown quite a few instances, it was often irritating and time consuming to get excellent. 

I am KICKING myself for not getting one sooner! This knocks off half the time of what I’d usually spend putting in crown molding. 

Whole sport changer. Now I am eyeing all of the rooms that would use this trim! 

Have you ever ever tried slicing crown molding? If it is intimidated you, I extremely counsel utilizing a jig like this to your noticed!