I’ve lastly begun getting my studio organized, and I began with organizing the provides for my present favourite pastime — making jewellery. I didn’t understand what number of provides and beads I had accrued till I began planning out how I used to be going to arrange them. However I got here up with a method to arrange all of it that I’m actually enthusiastic about. For somebody who doesn’t love the method of getting organized, I certain do love the outcomes after a company challenge is completed. 😀 I’ve gone again simply to have a look at and admire my newly organized storage closet many instances over the previous few days, and I’ve completed the identical factor with my jewelry-making provide drawers during the last 24 hours.
So let me present you what I did. Since jewelry-making provides are all fairly small, I made a decision to make use of three of the very shallow drawers on this center six-drawer cupboard.
And since I work on my jewellery tasks at my desk, I wanted a method to simply transport all of my provides and instruments to my desk, after which to simply deliver them again to the drawers to retailer them after they’re not in use.
My answer? Two very straightforward custom-made trays that match the drawers completely! Right here’s the drawer with the tray for all of my instruments and provides apart from the beads. Right here’s a view of it earlier than I added the entire gadgets to the tray so you may see how completely it matches the drawer. The perimeters of IKEA Sektion cupboard drawers are curved, which works out completely as a result of it leaves room for my fingers to wrap across the handles.
And right here’s what it appears to be like like with the provides and instruments on it…
So once I wish to work on some jewellery tasks, I can simply seize the entire tray and take it over to my desk…
To retailer my beads, I purchased two 40-pack containers of these 2-ounce clear jars (affiliate hyperlink). After which I saved them the wrong way up on the tray that I made for this drawer. For this drawer, I sized the tray to the jars slightly than making it to the precise dimension of the drawer in order that the jars wouldn’t slide round. The beads on the again are ones that I haven’t used but, so that they’re nonetheless intact from the shop.
This tray additionally makes it very straightforward to deliver all of my beads over to the desk, and since my desk is fairly huge, each trays match on the desk very simply, with loads of room left within the center for precise work house.
These trays had been really easy to make, they usually value me $0 as a result of I used scraps leftover from previous tasks. I began by slicing a chunk of 1/2-inch plywood to the size of the underside of the drawer, minus 1.5 inches for every measurement (size and width). Then I lower come scrap 1″ x 2″ lumber that I had already ripped on the desk noticed (once more, for a earlier challenge) in order that the acutal measurements had been 3/4 inch by 1 inch. I used my miter noticed to chop it to size in order that it match the precise dimension on the edges of the plywood, after which nailed it into place utilizing 16-gauge 1.5-inch nails. I repeated that on the opposite aspect.
After which I lower items for the back and front to cowl not solely the sting of the plywood, but in addition the ends of the aspect body items. In different phrases, I didn’t hassle to miter the corners. I simply lower all 4 items straight and nailed them on the sting of the plywood.
Then I used wooden filler on all 4 corners and the entire nail holes, after which sanded all the things clean with my sander and 150-grit sanding discs. I went again over all the things by hand and really shortly with 220-grit sandpaper earlier than priming and portray the trays.
I used Rust-Oleum spray primer, after which sanded once more by hand with 220-grit sandpaper earlier than portray the trays with a brush in Behr Polar Bear (my go-to white paint for trim). When that was dry, I brushed on two coats of General Finishes High Performance Topcoat in a matte finish (affiliate hyperlink). It’s my absolute favourite water-based topcoat, and regardless that it’s not beneficial to be used on white paint (for some motive, it may well yellow on white paint), I made a decision to probability it. That clean end is extra vital to me than the colour.
After which I had some leftover cupboard handles, so I used these as tray handles. And right here’s how the tray regarded when it was completed.
I nonetheless wish to get some felt pads to placed on the bottoms of the trays in order that I gained’t have the arduous wooden bottoms of the trays sliding on my desk. However apart from that, these drawers are effectively organized and really helpful.
I discussed that I used three of the drawers for my jewelry-making provides, however the third drawer didn’t require a {custom} sized tray. Right here’s what it appears to be like like for now…
I’m certain this drawer will finish holding extra gadgets sooner or later. However for now, it’s getting used to carry three issues. (1) I’ve a tray that holds my necklaces and earrings which can be in course of however haven’t been completed but. (2) I’ve a container that holds leftover beads from necklaces and earrings that I’ve already made. These don’t get their very own jars as a result of these aren’t seed beads or different filler beads that can be utilized time and again on a number of necklaces. These are extra specialty beads that I don’t actually wish to reuse as a result of I have already got a necklace made with them, and I don’t want one other. I’m undecided what I’ll find yourself doing with them. And (3) necklaces which can be completed, however they want changes.
I’ve room to develop in that drawer. In actual fact, there are issues on the primary provide and power tray that I don’t use usually, so I may truly transfer them to this drawer and provides my foremost tray a bit extra respiratory room. However for now, these drawers are completed and effectively organized with {custom} trays that make carrying all of my provides to my desk a breeze. I’m fairly enthusiastic about how this group challenge turned out!
Addicted 2 Adorning is the place I share my DIY and adorning journey as I transform and beautify the 1948 fixer higher that my husband, Matt, and I purchased in 2013. Matt has M.S. and is unable to do bodily work, so I do the vast majority of the work on the home on my own. You can learn more about me here.
Trending Merchandise
